Answer
The error code F8 E1 or LF or LO FL appears on the display of my Whirlpool washer. Code of Error After 13 minutes, the codes F8 E1, LF, and LO FL all indicate that no water has been detected entering the washer. Whenever a F8 E1, LF, or LO FL error occurs in the washer, the door will be locked and the control will become unresponsive.
As a result, one may wonder, what does FL Lo indicate on a washing machine?
When water is not detected entering the washer or when it is not filling the washer quickly enough, the Whirlpool washer Lo FL error code is shown on the screen. Check to see that the water supply hoses are not kinked or pinched, and that the screens in the water supply line are free of obstructions such as debris.
I also need to know how to clear the problem code on my Whirlpool washing machine?
Press the stop or cancel button twice, followed by the power button once, to delete the code. If the code is still on the screen, unplug the washer or turn off the power for one minute to clear it. During the Clean Washer cycle, it was discovered that there were items in the washer. Items should be removed from the drum before starting the Clean Washer cycle a second time.
What does the code f09 on a Whirlpool washing machine imply was also a question?
The error code E01 F09 on a Whirlpool Duet washer indicates a LONG DRAIN TIME. When your Whirlpool washer enters drain mode and the drain time has passed 8 minutes without reaching the reset level in the pressure sensor, the valves in the drain are shut off and the drain pump will stop pumping water out of the machine.
What does the FL Lo symbol on a Maytag washer mean?
F8 E1 or LF or LO FL or LF FL In the display of my Maytag washer, there is an error code. Code of Error After 13 minutes, the codes F8 E1, LF, and LO FL all indicate that no water has been detected entering the washer. Whenever a F8 E1, LF, or LO FL error occurs in the washer, the door will be locked and the control will become unresponsive.
There were 30 related questions and answers found.
What is the best way to clear the error code on my Maytag washer?
Press the stop or cancel button twice, followed by the power button once, to delete the code. If the code is still on the screen, unplug the washer or turn off the power for one minute to clear it. During the Clean Washer cycle, it was discovered that there were items in the washer. Items should be removed from the drum before starting the Clean Washer cycle a second time.
E1 error code on a Whirlpool washing machine means what?
Whirlpool Washing Machine Error Codes FP or F9 EIf your washing machine is not functioning properly, it is fair to assume that it has acquired a malfunction. A flashing FP or F9 E1 error number on the LCD display may be a cause for concern, but it’s most often related with an issue with the water draining from within the drum itself.
What does the FL code on a Samsung washer stand for?
The FL error code indicates that the door lock assembly is not functioning properly. A total of seven attempts will be made by the door lock to shut before an error code is shown on the display. Opening the door and removing the metal spring that surrounds the door gasket are two important steps. To remove the spring, you may use a putty knife or a flat head screwdriver.
What is the best way to reset my Whirlpool front-load washer?
Unplug the machine for 30 seconds to see whether the Duet washer control can be reset that way. Manually unlocking the washer may be accomplished by removing the top panel (remove the screws on the rear of the top panel and sliding the top panel back to pull the washer out).
What does the letter e1 on a washing machine mean?
According to my short investigation, an E1 Error number indicates that the machine is attempting to fill with water but is unable to detect when water has entered the machine. An obstructed intake valve, a failed inlet valve, a clogged pressure detecting line, or a failing water level sensor might all be the cause of this problem.
What does the error code f08 on a Whirlpool washing machine mean?
F08 indicates that the heater is an open circuit, therefore use a continuity tester to verify the heater for continuity. F12 indicates that one element has been shorted or that the heater has failed altogether; thus, it is required to replace the heater. On certain computers, the fault code F09 denotes an overflow problem, which implies that water has been discovered at the appliance’s base.
What does the code e1 f8 on a Whirlpool washer mean?
There are various probable reasons for a F8 E1 code, including the following: If the message F8 E1 or LF (too long to fill) shows on the display, it indicates that the washer is taking an excessive amount of time to fill. This washer contains sensors that detect when water is being supplied, and it needs that water be supplied to the water valve via both hoses.
How can I resolve the problem code f9?
The F9 error code often indicates that the door switch circuit system is malfunctioning. It is possible to resolve this issue simply inspecting the door switch itself. If the door switch is dusty or stuck in one place, wipe it off with a moist towel and then wriggle it gently to ensure that the switch slides back and forth between the positions.
What is the procedure for clearing the code on a Whirlpool f9?
F8 – Failure of the Control Board – Replace the control board (clock). F9 – Door Lock Failure in the Oven – Inspect the door lock switches and wiring. Keep an eye out for a jammed lock switch. FH – Detects the absence of water entering the machine or the absence of pressure. Select ‘cancel’ twice to erase this code from your computer. Switch Trip
What is the best way to clear the f9 code?
How to Disable the F9 Code on a Maytag Appliance Keep your finger on the “Start/Stop” button for a total of 10 seconds. The beeping will be silenced as a result of this. Open the oven door and make that the door lock is in good working order. If it wiggles, it is necessary to tighten it more. Apply a little amount of WD-40 on a washcloth and use it to brush away any rust or dirt from the latch. Close the oven door carefully with your fingers. Check the oven’s performance.
A Whirlpool washing machine’s pump may be cleaned in many ways.
Cleaning the Pump on a Whirlpool Washing Machine (with Pictures) Remove the electrical cable from the washer and plug it into a wall socket. Disconnect the drain hose from the drain or fixed tub and set it aside. Using a pair of slip-joint pliers, unscrew the water hose fittings from the machine and set them aside. Prepare the floor in front of the washer by laying an old blanket on it and tilting the washer forward so that it rests on top of the blanket.
ncG1vNJzZmivp6x7r6%2FEq6upp5mjwW%2BvzqZma2hiZ3xxfY6wn5qsXZm8pr%2BMn6NmpJ9iuqatzWamp2WRYsSptdGlp6innGLEor%2FHnqlnoKSiuQ%3D%3D